Outdoor Living Today CB96 Instruction Manual

9x6 Cabana Assembly ManualSome of the safety and usage measures you may wish to consider include:-snow load ratings vary by geographical location. If

16. Complete attachments of remainingside walls as per Steps 11-15.18. Position and attach both Window Walls as per Steps 11-15.1-888-658-1658

21. When all walls are attachedtogether, check alignment with the floor.Bottom of wall frame should sit flushwith outside of floor framing, with sidin

24. Place Side Gable Wall so 1x3 framing sits flush with theinside of the top plate. It should also be centered sideways onthe top plate. Adjust gable

C. Rafter and Roof SectionOutsideRoofPanels (2)Middle RoofPanels (2)Exploded view of all parts necessary to complete the Roof Section.Identify all pa

1-888-658-1658 www.outdoorlivingtoday.com [email protected] 1429. Attach end of a 52 1/2” long Soffit

30. Flip Rafter Section over soSoffit is down. Starting with the rearSection, lift completed rafters up andplace on gable framing. 31. Slide Rafter Se

35. With both Ridge Boards connected, completely secureGable framing to walls and rafters.Use 4 - 2” screws per Rafter. Usean additional 6 - 2” screws

37. Roof Gussets are positioned on mid rafters.Slide gusset up on side of rafters. Gusset must bebelow top edge of rafter. Use level to square gusset

40. Place Outside Roof Panel so it sits flush on 3rd rafter from the outside (doubled up rafter).Plywood on roof should be flush with end of rafter at

Outside PanelMiddle Panel Outside Panel43. Position and attach Front Roof Panels as per Steps 39-42. Toll Free 1-888-658-1658 www.outdoo

Parts List:A. Floor Section 3 - 35” x 75” - Floor Joist Frames 2 - 48” x 75” - Plywood Floor - Large1 - 9” x 75” - Plywood Floor - Small4 - 1 1/2” x 3

D. Miscellaneous SectionRidge CapsSideFacia (4)Rear Wall Narrow Trim (2)HorizontalGableTrim (4)Bottom SkirtingFront & Rear (6)Bottom Skirting (Sid

49. Attach Filler Trims (4 - 1/2” x 2 1/2” x 75”) to each corner side wall. Align Filler Trims so theysit flush with top of Bottom Skirting. Hammer w

52. Attach Rear Wall Narrow Trim(2 - 1/2” x 2 1/2” x 79”) where wallpanels come together and leave aseam. Position trim equally on wallseam and tight

55. Attach Front and Rear Facia to roof rafterends. There are 2 facia pieces per side. Securewith 8 - 1 1/4” finishing nails per piece. Side FaciaFr

Bottom Skirting61. Place Bottom Dutch Door panel intoposition, 3/8” gap on bottom and evenlyspaced on sides, and attach hinge todoorway seam trim wit

66. Attach Interior Door Stops to door framing(Jambs and Header). Start with Vertical piecesfirst. Stops should overlap doorway by 1/2”. Use4 - 1 1/4

Alternate Door Configuration (Door on Left or Right of Center)To configure the Cabana so the Dooris positioned on the left or right ofcenter wall pa

Congratulations on assemblingyour 9x6 Cabana!Note: Our Sheds are shipped as unfinished products. If exposed to the elements, the western redcedar lu

9X6 CABANA HARDWARE PACKAGE2 1/2”Note: screws and nails shown actual size.2”1 1/4”3/4”2” 3/4”1 1/4” 1 1/4”Tee Hinge x4Door HandleRidge Board Connecto

A. Floor SectionPlywood FloorLarge (2)Floor JoistFrames (3)Floor RunnersShort (3)Floor RunnersLong (3)Plywood FloorSmallExploded view of all parts nec

2. Both Outside Floor Joist Frames require 1 interior Floor Joist attachment. Center Joist (17 1/2”) from Outside of Floor Joist Frame to center of F

Note: The floor will be flipped over and floor runners will sit on your foundation. It is important to note that having a level foundationis critical

B. Wall SectionExploded view of all parts necessary to complete the Wall Section. Identify all partsprior to starting.8. Lay out all thewall panels

10. Starting at Rear Corner, position aSolid Wall Panel on top of plywood floor.Depending on your preference, you mayuse a solid or window wall panel

12. Position 1st side wall panel on plywoodfloor so once again 2x3 wall plate is sittingflush on floor. Position panel so 2x3 framingsits flush with r